Chapter – 11

Electricity

1. Introduction

Electricity runs our homes, schools, hospitals and industries. In this chapter we learn what makes up an electric current, what controls it, and how electrical energy is used and measured.

2. Electric Charge and Electric Current

  • The flow of electric charge is electric current. In metal wires, the charge carriers are electrons.
  • I = Q / t. SI unit of charge: coulomb (C); of current: ampere (A). 1 A = 1 C/s.
  • 1 C is the charge of about 6.25 × 1018 electrons. Charge of one electron = 1.6 × 10−19 C.
  • Current is measured by an ammeter, always connected in series.
  • By convention, the direction of current is opposite to the flow of electrons (from + to − terminal outside the cell).

Example 1: A current of 0.5 A flows through a bulb for 10 minutes. Charge = I × t = 0.5 × 600 = 300 C.

3. Electric Potential and Potential Difference

  • Charges flow only when there is a difference of electric pressure, called potential difference, as water flows only when there is a difference in level. A cell creates this potential difference by chemical action.
  • V = W / Q (work done to move a unit charge from one point to another). SI unit: volt (V). 1 V = 1 J/C.
  • Measured by a voltmeter, always connected in parallel across the two points.

Example 2: Work done to move 2 C of charge across a potential difference of 12 V: W = V × Q = 12 × 2 = 24 J.

4. Circuit Diagram Symbols

ComponentHow it is drawn
Electric cellOne long thin line (+) and one short thick line (−)
BatteryTwo or more cells joined
Plug key / switchOpen (OFF) or closed (ON) key symbol
Wire joint / crossingDot at a joint; crossing wires without a dot are not joined
BulbCircle with a cross
ResistorZig-zag line; variable resistor (rheostat) has an arrow
Ammeter / VoltmeterCircle with A / Circle with V

5. Ohm’s Law

At constant temperature, the current through a metallic conductor is directly proportional to the potential difference across its ends: V ∝ I, or V = IR. The constant R is the resistance, with SI unit ohm (Ω). 1 Ω = 1 V/A.

  • The V–I graph for a conductor is a straight line through the origin.
  • A rheostat is used to change resistance in a circuit.
  • Good conductors have low resistance; insulators have very high resistance.

Example 3: A bulb draws 0.5 A from a 220 V supply. Resistance R = V/I = 220/0.5 = 440 Ω.

6. Factors Affecting Resistance

Resistance of a conductor:

  • is directly proportional to its length (R ∝ l);
  • is inversely proportional to its area of cross-section (R ∝ 1/A);
  • depends on the nature of the material and temperature.

R = ρ l / A, where ρ (rho) is the resistivity of the material, SI unit Ω m. Metals and alloys have low resistivity (10−8 to 10−6 Ω m); insulators like glass and rubber have very high resistivity (1012 to 1017 Ω m).

  • Copper and aluminium are used for transmission wires (low resistivity).
  • Alloys like nichrome are used in heaters and irons: high resistivity and they do not oxidise (burn) easily at high temperature.
  • Tungsten is used for bulb filaments (very high melting point, 3380 °C).

Example 4: A copper wire is 2 m long with area of cross-section 1 × 10−6 m2. Resistivity of copper = 1.6 × 10−8 Ω m. R = ρl/A = (1.6 × 10−8 × 2) / (1 × 10−6) = 0.032 Ω.

Exam point: If a wire is stretched to double its length, its area becomes half, so its resistance becomes four times.

7. Resistors in Series and Parallel

PointSeriesParallel
Equivalent resistanceRs = R1 + R2 + R31/Rp = 1/R1 + 1/R2 + 1/R3
CurrentSame through each resistorDivides; total = sum of branch currents
Potential differenceDivides; total V = V1 + V2 + V3Same across each resistor
ResultTotal resistance is more than the largest oneTotal resistance is less than the smallest one

Example 5 (series): Resistors of 2 Ω, 3 Ω and 5 Ω are joined in series to a 10 V battery. Rs = 10 Ω; I = 10/10 = 1 A. Voltages: 2 V, 3 V and 5 V (total 10 V).

Example 6 (parallel): Resistors of 6 Ω and 3 Ω are joined in parallel to a 12 V battery. 1/Rp = 1/6 + 1/3 = 1/2, so Rp = 2 Ω. Total current = 12/2 = 6 A: 2 A through 6 Ω and 4 A through 3 Ω.

Why are household appliances connected in parallel? Each gets the full voltage, each can be switched on or off separately, and if one fails the others keep working. In series, one fused bulb would stop all others.

8. Heating Effect of Electric Current

When current flows through a resistor, some electrical energy turns into heat. This is the heating effect. According to Joule’s law of heating:

H = I2Rt

Heat produced is proportional to the square of current, to resistance, and to time.

Example 7: A current of 2 A flows through a 5 Ω resistor for 1 minute. H = 22 × 5 × 60 = 1200 J.

Practical applications: electric iron, toaster, oven, kettle, room heater, electric bulb (filament glows), and the electric fuse. A fuse is a wire of low melting point (alloy of tin and lead) connected in series. If current becomes too high, the fuse wire melts and breaks the circuit, protecting the appliances. Bulbs are filled with inert gases (nitrogen, argon) to make the filament last longer.

9. Electric Power

The rate at which electrical energy is used is electric power.

P = VI = I2R = V2/R. SI unit: watt (W). 1 W = 1 V × 1 A.

The commercial unit of electrical energy is the kilowatt hour (kWh), also called one “unit”. 1 kWh = 3.6 × 106 J.

Example 8: An electric heater is rated 1000 W, 220 V. Current I = P/V = 1000/220 ≈ 4.55 A. Resistance R = V2/P = 48400/1000 = 48.4 Ω.

Example 9: A 100 W bulb is used 10 hours a day for 30 days. Energy = 100 × 10 × 30 = 30,000 Wh = 30 kWh (30 units). At ₹5 per unit, the cost is ₹150.

10. Important Questions

Q1. What does an electric circuit mean?
Ans. A continuous, closed path of an electric current.

Q2. Why are coils of electric toasters and irons made of an alloy rather than a pure metal?
Ans. Alloys have higher resistivity and do not oxidise or burn easily at high temperatures.

Q3. How is a voltmeter connected in a circuit?
Ans. In parallel across the points between which the potential difference is measured.

Q4. Which uses more energy: a 250 W TV set in 1 hour or a 1200 W toaster in 10 minutes?
Ans. TV: 250 × 3600 = 9 × 105 J. Toaster: 1200 × 600 = 7.2 × 105 J. The TV uses more.

Q5 (long). Derive the formula for the equivalent resistance of three resistors in parallel.
Ans. In parallel, the same V is across each resistor and the total current I = I1 + I2 + I3. By Ohm’s law, I = V/Rp, I1 = V/R1, I2 = V/R2, I3 = V/R3. So V/Rp = V/R1 + V/R2 + V/R3. Dividing by V: 1/Rp = 1/R1 + 1/R2 + 1/R3.

Assertion–Reason: A: A fuse wire is connected in series with the appliance. R: The fuse must carry the whole current, so it can break the circuit when the current is too high.
Ans. Both true; R explains A.

11. Conclusion

Electric current is the flow of charge driven by potential difference. Ohm’s law links V, I and R, and resistance depends on length, area and material. Series and parallel combinations, the heating effect, and electric power explain how electricity is used and paid for in our homes.